Professional Tool Reviews for Pros

Many people want to know can a circular saw cut metal? The answer is: it depends. You have a lot of factors to consider in the metal-cutting vs circular saw question—like blade speed, the blade itself, and the collection of metal shavings created by the blade. You may look at your circular saw and wonder, “Why buy a metal saw when a framing saw does the same job?”

It’s a fair question and, actually, you could do that. Plenty of manufacturers make 7-1/4-inch metal cutting blades that will fit a standard circular saw. However, even the best circular saws fall short when you start comparing features specifically tailored toward metal-cutting applications.

Looking a little more closely at the metal-cutting circular saws might give us some insight into why Milwaukee, Makita, and others have created dedicated tools for cutting metal.

The Milwaukee M18 Fuel 7-1/4-inch circular saw has a no-load RPM of 5,800 whereas the Milwaukee FUEL 8″ metal saw comes in at 4,000. Even that steps up from the 3900 RPMs of their smaller model. Makita boasts a similar speed in their 18V LXT Brushless model. The blade speeds of a wood-cutting framing saw well exceed recommended cutting speeds of carbide teeth in metal.

But that’s not the whole story because you also want to watch the size of the blade. Not only do metal cutting saws spin at a lower RPM, but they sometimes use smaller blades. When they do, those teeth spin significantly slower than higher RPM, larger-bladed circular saws. Check out the router bit speed article we wrote which covers a similar issue for woodworking.

Standard metal-cutting circular saw blades typically fall into the 5-3/8-inch blade size. As noted above, however, Milwaukee makes a 7.5-inch saw. That’s significant since it allows for a maximum cut capacity of 2-9/16 inches. Smaller saws fall nearly 1-1/2 inches short of a standard size 7-1/4 inch framing saw blade and cannot cut through 2-inch conduit in a single pass.

Cutting metal presents a more difficult task than cutting wood. Metal cutting more closely resembles abrasion than chipping away large particles of material. 7-1/4-inch blades create a lot of sparks when they cut metal at high speed. That equals flying, flaming hot metal shards that can wear out a blade quickly.

The design of metal-cutting saws lets them either collect or deflect those shards better than a framing circular saw. Finally, but more generally, a traditional wood-cutting circular saw’s open housing might not protect against metal shard buildup. Metal-cutting saws typically have closed housings for that purpose.

Safety Tip: Always confirm the blade RPM rating is within the saw’s RPM rating. This also goes for metal-cutting chop saws.

As we mentioned earlier in this article, metal-cutting saws specialize in their tasks. With modern battery pack technology, they can make dozens of cuts—even through tough material like stainless steel. That means modern cordless metal-cutting saws can now do things only previously possible with corded tools.

We love that since it eliminates both a trip hazard and a common issue—cutting through the cord by accident. Our recommendation falls to corded saws if you need to save money and you intend to make a ridiculous amount of cuts. Corded saws also save on weight since they don’t require a battery pack.

For portability and flexibility, cordless metal-cutting saws rule the day and provide plenty of power and runtime.

It’s just not a good idea to use a wood cutting saw for metal cutting. Stick with circular saws designed for each specific task, and don’t be afraid to go for a corded metal cutting saw if a cordless model is too tough on your budget. You don’t want to burn up your circular saw and leave yourself without a tool to get your work done. Like so many others, it’s an expensive lesson to learn.

Shop Metal Saws at Acme Tools

On the clock, Kenny dives deep to discover the practical limits and comparative differences for all kinds of tools. Off the clock, his faith and love for his family are his top priorities, and you'll typically find him in the kitchen, on his bike (he's an Ironman), or taking folks out for a day of fishing on Tampa Bay.

What is a scroll saw used for? If you’re asking the question, be warned—once you know what a scroll saw […]

Today, we’re taking a closer look at the Flex FX1371 vs the Makita GDT01 impact driver in a head-to-head review. […]

GAU02 Pole Saw Helps You Trim Hard-To-Reach Branches If you’ve ever had to climb up a ladder to reach high-up […]

Makita Brings 40V XGT Tech To Commerical Lawn Mower Market With more Pro landscapers looking to replace or supplement their […]

What about using a plunge track saw with a metal cutting blade? Usually these saws have closed housings, smaller blades, lower or adjustable rotation speeds. On paper that would take care of the main issues, no? Any catch?

I used a cheap 10″ 4000 rpm sliding miter saw (Lowes)with 7 1/4 tenryu metal cutting blades to cut many thousand 5″ x 14 gauge steel plates. We would stack and clamp 5 plates (1/2″ thick and cut them quickly leaving an almost mirror finish. Chop saw will not work because the cut angle changes, but a circular saw would do well if the cut is perfectly straight and any vibration taken out of the metal. I would also rip and DADO 14 gauge plates on the table saw using zero clearance throatplates and a Grip-Tite (featherboard) holding down on…  Read more »

Nothing said about the blades!… I have used my Makita 5008MG 8 1/4″ circular saw, but using a 7″ diamond blade (PEARL PX-4000) rated for 8,730 RPM max. On my Makita 8 1/4″, the rotational speed is about 5,000 RPM under load, thus, with the 7″ blade, the peripheral speed is equivalent to 4,200 to 4,300 rpm… and seems to work perfectly good when cutting steel channel or angles. Of course, I have to remove the plastic dust collector adapter, buy otherwise it is acceptable for occasional use.

Can you use a metal skill saw with a wood blade and cut wood with it??. Do they even make a smaller wood blade?? And if you could cut wood, can you cut a 2×4 with it???

And what about the diamond blades??? Like the metalmax from lenox or the steelhead from milwaukee… They fit into the RPMs of the saws perfectly… They even have a Knock Out for your worm drive aka skilsaw…

As an Amazon Associate, we may earn income when you click on an Amazon link. Thanks for helping us do what we love.

See our Privacy Policy and Terms & Conditions.

Pro Tool Reviews is a successful online publication that has been providing tool reviews and industry news since 2008. In today’s world of Internet news and online content, we found that more and more professionals researched a large majority of their major power tool purchases online. That piqued our interest.

There’s one key thing to note about Pro Tool Reviews: We’re all about the professional tool user and tradesman!

Copyright ©2008-2022 Pro Tool Reviews, LLC. All rights reserved.